Getting Familiar with Plumbing: Your Starting Point for Bathtub Installation
Getting Familiar with Plumbing: Your Starting Point for Bathtub Installation
Blog Article
Just about every person will have their private conception when it comes to Tools You Need to Install a New Bathtub .
Setting up a tub isn't precisely brain surgery, yet it does need solid plumbing, woodworking, and also often, tiling abilities. Replacing an old tub with a brand-new one is likewise a reasonably difficult project. If the old bathtub is easily easily accessible, the job can relocate immediately; if you have to open up a wall surface to eliminate the old bathtub and also place the brand-new tub, the task is a lot harder. In either instance, the project is within a residence handyman's skills, although you will certainly require a helper to vacate the old tub as well as set in the new one. See to it you have certified on your own for the job and also fit trying it. Instead of working with a specialist to take control of a halfway-completed task, it is better to consider employing one before you start. Opportunities are you may require a professional plumber to make tube links.
This article will help you mount a brand-new bathtub in your shower room if you have already acquired a brand-new bathtub as well as don't require to change the arrangement of your previous water supply pipelines.
Your devices as well as product list ought to consist of the following:
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your installation, then the first thing you need to do is separate the supply of water. After doing so, switch on the faucets to drain any type of water remaining in the system. The process of getting rid of the existing taps can be fairly troublesome as a result of the limited access that is often the instance.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the faucets. Have a towel prepared for the remaining water that will certainly come from the pipelines. When the supply pipelines have been eliminated, make use of the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from transforming throughout this procedure. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any type of old sealing compound.
Prior to moving on to fit the brand-new faucets, compare the pipeline links on the old taps to the new faucets. If the old taps are longer than the new faucets, after that a shank adapter is required for the new faucets to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly require a plastic port to stop damage to the string. One end of the connector fits on the plastic tail of the tap as well as the other end provides a connection to the current supply pipelines.
If you require to fit a monobloc, after that you will need minimizing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, place the faucet in the mounting hole in the bath/basin making sure that the washing machines remain in place between the tap as well as the sink. Protect the tap in position with the maker given backnut. When the tap is firmly in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet adapters. The previous kind needs to be linked to the faucet finishes first, tightening just by hand. The supply pipes can later be linked to the other end. Tighten up both ends with a spanner after both ends have been linked.
Setting up the Tub
Utilizing the two wood boards under its feet, position the tub in the required position. The wood boards are handy in uniformly spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto four tiny factors.
The next objective is to ensure that the bathtub is leveled all round. This can be attained by inspecting the level and also readjusting the feet on the tub up until the level reviews level.
To install faucets, fit all-time low of the furthest versatile faucet connector to the suitable supply pipe by making a compression sign up with; after that do the exact same for the various other tap.
Turn on the water and also inspect all joints as well as brand-new pipework for leaks and tighten them if required. Fill up the tub and also check the overflow outlet and the normal outlet for leaks.
Ultimately, take care of the bath paneling as explained in the maker's user's manual. Tiling as well as sealing around the bathtub should wait until the bathtub has actually been utilized a minimum of once as this will certainly resolve it into its last setting.
Getting ready for the Installation
To start with, the sustaining structure provided with the bathroom ought to be fitted (if needed) according to the manufacturer's directions. Next off, fit the taps or mixer to the tub. When fitting the tap block, it is important to make sure that if the tap includes a plastic washing machine, it is fitted in between the bathroom and also the taps. On a plastic bathroom, it is additionally sensible to fit a sustaining plate under the faucets device to avoid stress on the tub.
Fit the versatile tap connectors to the bottom of both faucets utilizing 2 nuts and olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet via the hole in the bath. Use the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you utilize every one of the supplied washing machines.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom should now be ready to be fitted in its last placement.
Tiling Around the Bath tub
In the location where the bathroom meets the tile, it is required to seal the joins with a silicone rubber caulking. This is very important as the fitting can relocate sufficient to split an inflexible seal, creating the water to permeate the wall between the bath and the tiling, leading to difficulties with wetness as well as possible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to assimilate your fixtures and also installations. They are sold in tubes and also cartridges, as well as are capable of securing voids as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can load it with twists of drenched paper or soft rope. Remember to always fill up the bathtub with water prior to sealing, to enable the motion experienced when the bathtub is in use. The sealant can break relatively early if you do not take into consideration this motion before sealing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally quickly available on the marketplace. It is a good idea to fit the ceramic tiles making use of waterproof or waterproof glue and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As an enthusiastic reader on How to Install a Bathtub Yourself, I was thinking sharing that blog post was really useful. For those who liked our blog posting plz be sure to share it. Thanks for your time. Kindly pay a visit to our site back soon.
Urgent plumbing? Call us. Report this page